GfG 3300-11-013, CC33, Fixed Transmitter, Transmitter with sensor -Stainless Steel catalytic sensor 0-100% LEL (MK 208-3), Propane (C3H8) - RS 485 No Relay

CC33, Fixed Transmitter, Transmitter with sensor -Stainless Steel catalytic sensor 0-100% LEL (MK 208-3), Propane (C3H8) - RS 485 No Relay, GfG 3300-11-013

CC33 Fixed Transmitter, stainless steel, for very demanding applications, by GfG Instrumentation

CC33 transmitter with stainless steel enclosure, for flammable gases and vapors with ignition protection type "d".

If flammable gases and vapors need to be monitored safely in Ex zones under demanding conditions such as in the food industry, the CC33 transmitter with its unpainted stainless steel housing is an extremely robust and reliable solution. The CC33 transmits measured values and status indications either on analog (4-20 mA) or digital (RS-485) signal. The current measured gas concentration is also shown on its LC display. The special stack effect ensures very short response times of only a few seconds for a quick warning of explosion hazards. Three relay outputs provide additional alarm options. In combination with GfG's reliable controllers, it can be installed in new gas detection systems or retrofitted into existing ones.

The CC33 uses catalytic combustion (CC) to detect flammable gases and vapors such as methane, propane and hydrogen as well as ammonia. Their long-life sensors make 33 series transmitters an economical solution for detecting a wide range of combustible gases in the measuring ranges 0 to 100 % LEL and 0 to 4 % by volume (NH3). Its automatic temperature compensation and the linearization of the measuring signals ensure high measuring accuracy. In the event of an alarm, two red LEDs light up and the display color changes to red. The three optional relay outputs can be used to automatically trigger an explosion-proof buzzer, visual warnings such as flashing lights or the ventilation in case of an alarm.

Communication and service

Signals are transmitted on the analog industrial standard (4-20 mA) or via the digital RS-485 interface (Modbus protocol). The CC33 is also able to utilize ACDC technology, which enables it to transmit digital data on analog, three-wire lines in systems using an ACDC-capable controller. It uses two status LEDs to indicate its operating status and also features two additional alarm LEDs and three relay LEDs. Service and adjustments can be carried out on site with a magnetic pen and three magnetic buttons behind 15 mm thick bullet-proof glass (one-person adjustment). The pre-adjusted sensors can be easily replaced thanks to Smart Sensor technology. The multi-color backlit display shows the current measured value, status messages and the CC33's menu. Test gases for function tests can be inserted using a calibration adapter. Alternatively, when the device is mounted in a difficult-to-reach location, an optional remote calibration adapter can be used without impairing the transmitter's stack effect.

Explosion and device protection

The CC33 is approved for use up to Ex zone 1 and meets the requirements of ignition protection type "d" (flameproof enclosure). The unpainted stainless steel housing and Viton seals guarantee a long operating time even in the toughest conditions. The transmitter is protected against the ingress of dust and water according to IP54. If required, the protection class can be raised to IP67 with additional thread seals. For any applications not requiring a stainless steel housing, the CC33 is also available in a painted aluminum housing.

Key features and General Information at a glance:

• Measuring principle: catalytic combustion (CC).
• For flammable gases and vapors.
• Pressure-resistant encapsulated housing made of stainless steel with bulletproof glass (15 mm).
• 2.2 inch color display.
• Expected sensor lifetime: 5 years.
• Signal transmission: 4-20 mA / RS-485 / ACDC.
• Protection class: IP67 (with thread sealing, otherwise IP54).

Approvals / Certifications:

• ATEX certification: II 2G Ex db IIC T6 Gb (II 2G Ex db ib IIC T4/T6 Gb with buzzer).

Optionally available:

• Three relay outputs, magnetic rod, windscreen, flow adapter, remote calibration adapter, buzzer, threaded plug, cable gland.

Detectable Gases

LEL combustible gases, C₂H₂ Acetylene, C₂H₄ Ethylene, C₂H₆O Ethanol, C₂H₆ Ethane, C₂H₆O Dimethyl ether, C₃H₄ Propine, C₃H₆ Propene, C₃H₆O Acetone, C₃H₆O₂₂ Methyl acetate, C₃H₈ Propane, C₃H₈O n-Propanol, C₄H₈O 2-Butanon (MEK), C₄H₈O₂ Ethyl acetate, C₄H₁₀ n-Butane, C₄H₁₀O n-Butanol, C₅H₁₂ Pentane (n), C₆H₆ Benzene, C₆H₁₂ Cyclohexane, C₆H₁₂O Methyl isobutyl ketone (MIBK), C₆H₁₄ n-Hexane, C₇H₈ Toluene, C₇H₁₆ n-Heptane, C₈H₁₈ Octane (n), C₉H₂₀ n-Nonane, CH₄ Methane, CH₄O Methanol, CO Carbon monoxide, H₂ Hydrogen, NH₃ Ammonia.

HAZMAT Item: No

New: Yes

Type: 3300-11-013, CC33, Fixed Transmitter